Setting the motor data Prior to commissioning, the motor controller requires a number of values from the motor data sheet. Number of pole pairs: Object 2030h:00h (pole pair count) The number of motor pole pairs is to be entered here. With a stepper motor, the number of pole pairs is calculated using the step angle, e.g., 1.8° = 50 pole pairs, 0.9° = 100 pole pairs (see step angle in motor data sheet). Object 6075h:00h: rated current of the motor in mA (see motor data sheet) Object 6073h:00h: maximum current (for a stepper motor, generally corresponds to the rated current, bipolar) in tenths of a percent of the set rated current (see motor data sheet). Factory settings: "1000", which corresponds to 100% of the value in 6075h. Object 3219h:01h Maximum duration of the maximum current (6073h) in ms (for initial commissioning, Nanotec recommends a value of 100 ms; this value is to be adapted later to the specific application). Setting the motor type: Stepper motor: Object 3202h (Motor Drive Submode Select): Set bit 6 to "0" for stepper and choose via Bit 0 bewtween open and closed loop: value 0h or 1h.See also chapter Commissioning open-loop. Object 3219h:03h (Open loop idle state current): value in tenths of percent, to which the rated current is to be reduced if current reduction is activated in open-loop. BLDC motor: Object 3202h (Motor Drive Submode Select): Bit 6 for BLDC, bit 0 for recommended closed-loop: 00000041h Motor with encoder without index: You must set the encoder parameters after the Auto setup, see chapter Configuring the sensors. Stepper motor, brake control activated: 00000004h BLDC motor, brake control activated, closed-loop: 00000045h Note: Due to the sine commutation and the sinusoidal current flow, the current of a motor winding can achieve an alternating current value that is briefly greater (by max. √2 times) than the set current. At especially slow speeds or while at a standstill with full load, one of the windings can therefore be supplied with overcurrent for a longer period of time. Take this into account when dimensioning the motor and select a motor with larger torque reserve if necessary if required by the application.
Setting the motor data Prior to commissioning, the motor controller requires a number of values from the motor data sheet. Number of pole pairs: Object 2030h:00h (pole pair count) The number of motor pole pairs is to be entered here. With a stepper motor, the number of pole pairs is calculated using the step angle, e.g., 1.8° = 50 pole pairs, 0.9° = 100 pole pairs (see step angle in motor data sheet). Object 6075h:00h: rated current of the motor in mA (see motor data sheet) Object 6073h:00h: maximum current (for a stepper motor, generally corresponds to the rated current, bipolar) in tenths of a percent of the set rated current (see motor data sheet). Factory settings: "1000", which corresponds to 100% of the value in 6075h. Object 3219h:01h Maximum duration of the maximum current (6073h) in ms (for initial commissioning, Nanotec recommends a value of 100 ms; this value is to be adapted later to the specific application). Setting the motor type: Stepper motor: Object 3202h (Motor Drive Submode Select): Set bit 6 to "0" for stepper and choose via Bit 0 bewtween open and closed loop: value 0h or 1h.See also chapter Commissioning open-loop. Object 3219h:03h (Open loop idle state current): value in tenths of percent, to which the rated current is to be reduced if current reduction is activated in open-loop. BLDC motor: Object 3202h (Motor Drive Submode Select): Bit 6 for BLDC, bit 0 for recommended closed-loop: 00000041h Motor with encoder without index: You must set the encoder parameters after the Auto setup, see chapter Configuring the sensors. Stepper motor, brake control activated: 00000004h BLDC motor, brake control activated, closed-loop: 00000045h Note: Due to the sine commutation and the sinusoidal current flow, the current of a motor winding can achieve an alternating current value that is briefly greater (by max. √2 times) than the set current. At especially slow speeds or while at a standstill with full load, one of the windings can therefore be supplied with overcurrent for a longer period of time. Take this into account when dimensioning the motor and select a motor with larger torque reserve if necessary if required by the application.
